Residential · Toilets, sinks & showers
Faucet Repair and Replacement in Markham
A dripping faucet wastes water day and night, and a stiff or wobbly handle makes every use a chore. Many faucets can be repaired; some are simply ready to retire.
- Caulk and grout lines checked around the fixture
- Parts matched to the brand you already have
- Seized stops replaced while we are there
- Old fixtures and packaging taken away
- Licensed plumbers (details on request)
- Price agreed before work
- Call-only, no forms
- Tested before we leave
Signs you need faucet repair or replacement
A steady drip at the spout although the handle is fully closed. Water seeping around the base or under the handle. A handle that's stiff, loose or hard to control. Low flow from one faucet while others in the house are fine. Corrosion or worn finish on the body. A spray or pull-down hose dripping in the cabinet below. These are all worth a look, and the right fix depends on the faucet's design.
Our routine on the day
We identify the faucet type first: compression, ball, cartridge or ceramic disc. Each uses different internal parts. For a dripping cartridge faucet, the cartridge is usually replaced. For older compression faucets, seat washers and O-rings are the typical culprits. Ceramic disc faucets may need cleaning or a seal replacement.
We check the aerator for mineral build-up when flow is low, and inspect the supply lines and shut-off valves under the sink. If the faucet is very old, corroded, or parts are no longer available, replacement often makes more sense. In that case, the old faucet is removed, the deck cleaned, and the new faucet installed with fresh supply lines. Everything is tested for leaks at full pressure.
Markham houses and what shapes this job
Hard water in York Region shortens the life of faucet cartridges and aerators. Mineral deposits wear seals and clog small passages, which is why low flow and drips are common complaints across Markham. A water softener reduces this wear considerably.
Homes in established areas such as Markville, Raymerville and Royal Orchard often have faucets dating back to the 1980s or 1990s. Parts for those models can be hard to find. Newer homes in Wismer Commons and Cathedraltown generally have widely supported brands with readily available cartridges.
Shut-off valves under sinks are often overlooked. Older multi-turn valves can seize or leak once they are disturbed. We test them before starting and replace them if needed, since a valve that will not close makes future repairs more difficult.
Kitchen and bathroom differences
Kitchen faucets often have pull-down sprayers, soap dispensers and wider spans. Bathroom faucets may be single-hole, centreset or widespread. We confirm the hole configuration before you shop, so a new faucet fits without drilling.
When the job is finished, we leave the old parts out for you to see if you would like, and wipe down the basin and cabinet before we pack up.
Ring us without delay if
Call promptly if water is leaking under the sink into a cabinet, since that can damage the base and floor. A dripping spout is less urgent but still worth fixing. For outdoor taps, see outdoor faucet repair.
Before a call: note the brand if you can see it on the faucet or handle.
From the job notes of Plumbers in Markham
Job card · Toilets, sinks & showers
On the van for this job
- Wax rings, closet bolts, flappers and fill valves
- Cartridges for common shower and faucet brands
Signs you need this
- The toilet runs or refills on its own
- The shower goes scalding when someone flushes
What we check before we pack up
- Fill and drain the fixture and watch every joint
- Set temperature limits on shower valves
| Fixture | Parts that wear | What to know |
|---|---|---|
| Toilet | Flapper, fill valve, wax ring | Rocking means bolts or wax |
| Shower valve | Pressure-balance cartridge | Access panel saves tile |
How the job runs, start to finish
- 1
On the phone
Explain what the water is doing and where. We ask the age of the house and which valve or breaker to shut while we drive over.
- 2
Drop cloths down
Floors and cabinets get covered, the water or gas is isolated and the work area is lit.
- 3
Find the failed part
We open the trap, cleanout, access panel or wall where the fault is, and show you what we found.
- 4
Quote, then work
We explain what failed and what the fix costs; no cutting starts until you say yes.
- 5
Cut, fit, seal
Old parts come out, new pipe, valves or fixtures go in, and joints are soldered, pressed, crimped or glued.
- 6
Test and ticket
We run water, pressure-test or fire the heater, check for drips, clean up and leave a written ticket of what was done.